Dexon Canada Ventilation Equipment
- Indoor Wall Mount -

Print this page


The temperature leaving the unit is maintained at an adjustable preset temperature. Typically, if the discharge air temperature drops below 0º C the power to the fan and element is shut off in “Low Temp” condition to prevent freezing. A timer overrides the low temperature signal for an initial period of approx. 8 minutes every time the blower heater is reset at the status board, or control power is cycled.  The blower heater will automatically restart again once the temp sensor detects 2º C or more.  A high temperature sensor will cut the power to the heating elements if it senses temperatures above the normal operating range. After cooling down the elements will automatically restart if there is a demand.


Solid state controller designed and manufactured by Dexon provide the following features:

  • DISCHARGE TEMPERATURE SENSOR - A sensor located in the discharge air flow monitors the temperature leaving the unit to maintain a preset temperature and will also activate the Low Temp Shut Down
  • LOW TEMP SHUT DOWN - The Discharge Temperature Sensor sends a signal to the controller to shut down the fan and elements in the unit when the discharge temperature drops below 0º C (typically)
  • LOW TEMP SHUT DOWN OVERRIDE- At start up or upon reset a short period of time is provided to allow the elements time to warm up the sensor to prevent  the unit from going into a Low Temp Shut Down condition. The manual switch will also override the Low Temp. Shut down
  • OVERHEAT PROTECTION - A High Temperature Sensor located above the elements will cut power to the elements if it senses temperatures above the normal operating range. Class 1, Div. 2, Group C & D Locations will also have a sensor on each element. As sensors cool the elements will automatically restart if there is a demand
  • PROOF OF FAN ROTATION – Provides indication of a no air condition on the status board and if the optional alarm module is used will initiates a “No Air” alarm when the fan stops in the event of a fan failure, or when a low temperature shut down condition occurs. When the “No Air” LED is on, it also cuts the power off to the heating elements.
  • FAN SPEED CONTROL - A potentiometer is provided on the controller to preset and adjust the fan speed to deliver the desired air flow
  • FAN BOOST START - A full voltage boost start is applied to the fan upon start up before the fan goes into it’s preset speed to ensure a start up in a low speed setting
  • ELEMENT STAGING - The controller will activate stages two and three as required to maintain the preset discharge temperature, and will also send a signal to the Status Board to corresponding stages
  • STATUS INDICATION - The controller provides power and output signals to a remote Status Board to provide the following indications:

“Power On” - indicates control power is present at main controller
“No Air” – Indicates the fan has stopped in the event of a fan failure or when a low temperature shut condition has occurred and also cuts the power off to the heating elements.
“Low Temp.” - indicates elements are no longer able to maintain the preset temperature. The unit will completely shut down unless Low Temp Shut Down is overridden by timer or manual switch 
“Over Heat” - indicates an overheat condition has occurred
“Element No. 1” - indicates element is on, with the LED modulating on and off, as required to maintain the preset temperature
“Element No.2" - indicate elements in stage two are required to maintain the preset temperature. This LED will not modulate
“Element No.3" - indicate elements in stage three are required to maintain the preset temperature. This LED will not modulate
“Man. Fan” – will turn fan to max speed and override the Low Temp Shut Down. The normal operating position for this switch is on “Auto”
“Reset” - a reset switch is provided to restart the unit after a low temp condition has occurred, and also initiates the low temp override timer

Status Info
  • ALARM MODULE - An optional Alarm Module is provided that would mount to the back of the status board to provide alarm for either a “No Air” , “Low Temp” , or “Overheat” condition, or any combination of the three.  This Alarm Module will interface with warning devices such as automatic telephone dialing equipment, central monitoring devices, or other audible or visual alarms, etc..


  • Control voltage  120 V 60 Hz at 150 to 1200 watts maximum
  •  Control fused as per configuration requirements. Fused remote (by others) for Class 1, Div.2 Locations and fused internally for Ordinary Locations
  • Element voltage 208, 240, 480, or 600 Volt, one or three phase, from 3000 to 40500 watts maximum
  • Elements must be fused remote as required based on capacity
  • A standard 8 meters of status cable is provided
  • A separate conduit is required for power, status board, and optional interfacing features used


  • Provide a discharge duct as per shop drawings, dimensions will vary with capacity. Typical discharge is a rectangular protruding collar. An internal transition may be provided for a round protruding discharge if requested
  • Provide air inlet rough opening in wall as per shop drawings 
  • An outdoor surface mount louver section is provided for exterior wall mounting
  • Avoid mounting unit with louvers facing prevailing winds
  • Adjustable wall mounting brackets are supplied for mounting to interior wall
Power On No Air Low Temp Over Heat Element No.1 Element No.2 Element No.3 Warning Message Reset Switch Fan Switch
Site by B Smith Media
Copyright © 2011 Dexon Canada Air Systems Inc.